DK-M3-RS-U-1M-20

APPLICATIONS
Only 12 mm in diameter, this system is
ideal for precise, point-to-point beam
steering in a limited space, where dynamic
scanning is limited to less than 100 Hz.
The 3.3 VDC input makes it suited for
handheld and portable instruments.
Medical
 Dermatology lasers, fluorescence
microscopes and imaging instruments
 In-vivo and in-vitro micro laser surgery
Industrial
 3D printers
 LIDAR, 3D measurement, spectroscopy
 Remote sensing (e.g. pollution sources)
 Image and hand tremor stabilization
 Laser marking, engraving, machining
Telecommunications
 Free-space optical communication
 Variable optical attenuation
 Fiber-to-fiber optical switching
Aerospace and Defense
 Target designation, jitter compensation
 Automated obstacle detection, tracking
and avoidance for robots, UAVs, etc.

상품코드: 5801948
카테고리:
태그: , ,

Mirror positioning on your fingertip
The DK-M3-RS-U-1M-20 is a complete piezoelectric mirror
positioning system with a familiar galvo-scanner form factor, but
a drastically smaller size: only 12 mm diameter including the
embedded closed-loop controller.

The mounted aluminum-coated mirror moves at up to 1100
degrees per second with accuracy of 0.25 degrees for precise,
point-to-point positioning. The mirror range is +/- 20 degrees.

Embedded controller means tiny size plus
fast, easy integration
Patented piezoelectric motors along with position sensors,
bearings, drive electronics and embedded firmware are all
integrated into the miniature rotary stage.

We’ve eliminated the extra bulk of a separate external controller.

Along with smallest system size, this makes for fast, easy
integration into your system. The positioner accepts direct input
of high-level digital motion commands from your system
processor, or use the USB adapter for PC control.

Low power for hand-held systems
The mirror positioning system needs only 3.3 V DC and uses
approximately 500 mW when moving or 50 mW in standby mode.
It can be powered by USB or standard batteries. The integrated
piezo motor holds position without using power.

M3-RS-U smart stage with standard mounted mirror
Beam Diameter (maximum) 2 mm
Range of Motion +/- 20 deg
Speed >1100 deg/sec
Acceleration >1,000,000 deg/sec2 *
Stall Torque (minimum) 0.04 N-mm
Holding Torque (minimum) 0.08 N-mm (zero power)
Recommended Maximum Payload mounted to rotating shaft (Payload

must be balanced)

Mass 3g
Inertia 350 g-mm2
CLOSED-LOOP performance (with built-in position sensor)
Recommended Step Frequency Up to 100 Hz
Resolution (encoder resolution) 0.025 deg (440 µrad) absolute
Repeatability +/-0.05 deg (880 µrad)
Accuracy 0.25 deg (4400 µrad)
Maximum Closed-Loop Step & Settle Times (0.99 g-mm2 inertial load*)
0.5 deg 9 ms
5 deg 14 ms
20 deg 21 ms
OPEN-LOOP performance (external position sensor provided by user)
Resolution <0.0057 deg (<100 µrad)
Accuracy Typically better than 10% of distance

travelled after calibration

Maximum Open-Loop Step Times (0.99 g-mm2 inertial load*)
0.05 deg 0.5 ms
0.5 deg 1.6 ms
5 6 ms
20 deg 10 ms
Input Voltage 3.3 V DC
Power Consumption (typical)
Input directly to stage 500 mW active, moving

190 mW active, ready

50 mW standby

Input via USB interface

(break-out board)

675 mW active, moving

365 mW active, ready

150 mW standby

Stage Mass 3g
Operational Lifetime > 2,000,000 random positions**
Temperature/Relative Humidity 0 to +60 C, non-condensing
Compliance CE / RoHS
Communication Interface I2C, SPI, UART, analog servo

Input directly to M3-RS

Controller Integrated into stage, 64 MIPS

NO external controller needed